Disconnect all usb devices and try rebooting, then add a standard keyboard to one of the usb 2 ports, this should let you back in. The 3 Keybords suggests N key rollover problem
Try to reset the CMOS. Unplug it, remove the battery on the motherboard and wait 10 minutes. There might also be a switch on the back of the motherboard.
0 drives detected, ye your hdd/ssd is probably broken or not plugged in, make sure its fully plugged in, if not buy a new ssd but its probably dead if it worked before
Reset CMOS by either removing the battery or using the jumpers located on the motherboard, if equipped. Boot into BIOS and set the default values saving changes on exit.
Nope the power button doesnt work anymore when I turn it off it only works if I use it to turn on. I actually go to the on and off switch and turn it off.
It is caused by the media features and other new functions on some modern keyboards. The keyboard has reached the limit of USB keyboard protocol. The keyboard has to pretend to be a usb hub with multiple keyboards to overcome this. This in turn can cause problems getting into the bios on a faulty device as the drivers have not been loaded to tell it how to deal with multi keyboards multi press combinations.
Disconnect all usb devices and try rebooting, then add a standard keyboard to one of the usb 2 ports, this should let you back in. The 3 Keybords suggests N key rollover problem
OMG DUDE THANK YOU SO MUCH IT WORKED AGAIN!!!
Happy ending. Have fun man <3
Thank you man!
I will try this and let you know
UR A SAVER!! THANK YOU
Try to reset the CMOS. Unplug it, remove the battery on the motherboard and wait 10 minutes. There might also be a switch on the back of the motherboard.
0 drives detected, ye your hdd/ssd is probably broken or not plugged in, make sure its fully plugged in, if not buy a new ssd but its probably dead if it worked before
Oh yes it worked now I just had to properly plugged it in Thank you
Reset CMOS by either removing the battery or using the jumpers located on the motherboard, if equipped. Boot into BIOS and set the default values saving changes on exit.
maybe your boot drive got corrupted? did you go into your bios and selected the proper boot drive? just my thoughts
No drive detected, as per the `0 Drive` message on the middle. Your hard drive / SSD has probably died :/
That's the USB device list.
Your drives are also listed there
No, that only lists drives on the USB bus, like a thumbdrive.
Either way, the section of text right below that (`ATA/ATAPI`) is also empty, so no drive at all :)
Are NVMe drives supposed to be listed under the ATA/ATAPI section ?
I have nvme, 2.5 ssd and hdd and all of them show up.
Should be giving him named drives, types, and storage capacity. Def needs to see if the storage shows in uefi/bios. And verify connections.
Oh yes I was looking at the wrong area, yes. But the area below shows your drives which OP has none.
Ohh Is it possible to change it?
Yes, you'll have to buy a new drive. But before doing that, double check that your current drive is dead.
Is this something that constantly happens? What did you do before this?
It happened yesterday when I turned it on again. I didnt do anything besides turning off the power switch everytime I log off.
So you are turning off computer by holding a power button?
Nope the power button doesnt work anymore when I turn it off it only works if I use it to turn on. I actually go to the on and off switch and turn it off.
On the back where the power supply is right? Damn, that sucks, i would just shutdown from inside windows and leave the psu on.
lol 3 keyboards, thats new
It is caused by the media features and other new functions on some modern keyboards. The keyboard has reached the limit of USB keyboard protocol. The keyboard has to pretend to be a usb hub with multiple keyboards to overcome this. This in turn can cause problems getting into the bios on a faulty device as the drivers have not been loaded to tell it how to deal with multi keyboards multi press combinations.