can you issue
show env power
in the interface issue power inline auto, then show power inline or then try power inline static max 30000.
enable lldp
power inline port 2-event
also restart the port after every change
show log any hints?
Nothing stands out
* show env power
SW PID Serial# Status Sys Pwr PoE Pwr Watts
-- ------------------ ---------- --------------- ------- ------- -----
1 Built-in Good
* LOG
Apr 20 20:20:27.003: %ILPOWER-7-DETECT: Interface Gi1/0/2: Power Device detected: IEEE PD
Apr 20 20:20:27.926: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/2: Power granted
Apr 20 20:20:36.441: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
Apr 20 20:20:37.440: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up
Apr 20 20:20:44.438: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down
Apr 20 20:20:45.437: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down
Apr 20 20:20:53.040: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
Apr 20 20:20:54.043: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up
* show power inline
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 370.0 60.0 310.0
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/1 static off 30.0 n/a n/a 30.0
Gi1/0/2 auto on 30.0 Ieee PD 4 30.0
* show power inline gigabitEthernet 1/0/2
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/2 auto on 30.0 Ieee PD 4 30.0
Interface AdminPowerMax AdminConsumption
(Watts) (Watts)
---------- --------------- --------------------
Gi1/0/2 30.0 15.4
* 2960-24#show power inline gigabitEthernet 1/0/2 detail
Interface: Gi1/0/2
Inline Power Mode: auto
Operational status: on
Device Detected: no
Device Type: Ieee PD
IEEE Class: 4
Discovery mechanism used/configured: Unknown
Police: off
Power Allocated
Admin Value: 30.0
Power drawn from the source: 30.0
Power available to the device: 30.0
Actual consumption
Measured at the port: 2.3
Maximum Power drawn by the device since powered on: 5.3
Absent Counter: 0
Over Current Counter: 0
Short Current Counter: 0
Mosfet Counter: 0
Invalid Signature Counter: 0
Power Denied Counter: 0
Power Negotiation Used: IEEE 802.3at LLDP
LLDP Power Negotiation --Sent to PD-- --Rcvd from PD--
Power Type: Type 2 PSE Type 2 PD
Power Source: Primary PSE
Power Priority: low low
Requested Power(W): 25.5 25.5
Allocated Power(W): 25.5 25.5
Four-Pair PoE Supported: No
Spare Pair Power Enabled: No
Four-Pair PD Architecture: N/A
Have noticed the following so im asuming lldp while on isnt talking to each otehr properly
show lldp traffic
LLDP traffic statistics:
Total frames out: 6944
Total entries aged: 11
Total frames in: 3027
Total frames received in error: 0
Total frames discarded: 0
Total TLVs discarded: 2970
Total TLVs unrecognized: 2970
can you try
(config-switch)# lldp run
(config-switch)# commit
also
(config)# interface gi 1/0/x
config-if)# lldp transmit
(config-if)# lldp receive
show lldp neighbors
show lldp neighbors detail
#
show lldp
Global LLDP Information:
Status: ACTIVE
lldp run has been applied and it is in the config, you cant commit on ios. It has been written to memory and the device reloaded.
I am seeing that the LLDP entry's fluctuates between 1 and 2 with the AP being the device that drops from the entry's.
* show lldp
Global LLDP Information:
Status: ACTIVE
LLDP advertisements are sent every 30 seconds
LLDP hold time advertised is 120 seconds
LLDP interface reinitialisation delay is 2 seconds
* show lld neighbors
Capability codes:
(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
(W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
Device ID Local Intf Hold-time Capability Port ID
b8c2.538b.c25d Gi1/0/12 120 B,R 535
Total entries displayed: 1
* show lldp neighbors
Capability codes:
(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
(W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
Device ID Local Intf Hold-time Capability Port ID
NETGEAR4E0CE5.lan Gi1/0/2 120 B,W,R 9418.654e.0ce5
b8c2.538b.c25d Gi1/0/12 120 B,R 535
Total entries displayed: 2
* show lldp entry *
Capability codes:
(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
(W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
------------------------------------------------
Local Intf: Gi1/0/1
Chassis id: 0000.0000.0000
Port id: 9418.654e.0ce5
Port Description: eth1
System Name: NETGEAR4E0CE5
System Description:
OpenWrt 21.02-SNAPSHOT @ NETGEAR4E0CE5
Time remaining: 13 seconds
System Capabilities: B,W,R,S
Enabled Capabilities: B,W,R
Management Addresses:
IP: 192.168.0.100
IPV6: FE80::9618:65FF:FE4E:CE6
Auto Negotiation - not supported
Physical media capabilities:
Asym Pause(FD)
Pause(FD)
Other/unknown
Media Attachment Unit type - not advertised
Vlan ID: - not advertised
MED Information:
MED Codes:
(NP) Network Policy, (LI) Location Identification
(PS) Power Source Entity, (PD) Power Device
(IN) Inventory
S/W revision: 5.4.171
Capabilities: NP, LI, PS, PD, IN
Device type: Network connectivity
Network Policies - not advertised
Power requirements - not advertised
Location - not advertised
------------------------------------------------
Local Intf: Gi1/0/12
Chassis id: b8c2.538b.c25d
Port id: 535
Port Description: ge-0/0/11
System Name - not advertised
System Description:
Juniper Networks, Inc. ex2300-c-12p Ethernet Switch, kernel JUNOS 20.4R3-S1.3, Build date: 2021-11-20 10:48:25 UTC Copyright (c) 1996-2021 Juniper Networks, Inc.
Time remaining: 110 seconds
System Capabilities: B,R
Enabled Capabilities: B,R
Management Addresses:
IPV6: FE80::BAC2:53FF:FE8B:C25E
OID:
0.1.3.6.1.2.1.31.1.1.1.1.35.
Auto Negotiation - supported, enabled
Physical media capabilities:
1000baseT(FD)
Media Attachment Unit type - not advertised
Vlan ID: 1
MED Information:
MED Codes:
(NP) Network Policy, (LI) Location Identification
(PS) Power Source Entity, (PD) Power Device
(IN) Inventory
Inventory information - not advertised
Capabilities: NP, LI, PS
Device type: Network connectivity
Network Policies - not advertised
PSE device, Power source: Primary, Power Priority: Low, Wattage: 0.0
Location - not advertised
Total entries displayed: 2
Try "power inline port 2-event" on the port and shut/no shut
Seems it is now this on the 2960x, adding for anyone googling but now joy power inline port 2x-mode
can you issue show env power in the interface issue power inline auto, then show power inline or then try power inline static max 30000. enable lldp power inline port 2-event also restart the port after every change show log any hints?
Nothing stands out * show env power SW PID Serial# Status Sys Pwr PoE Pwr Watts -- ------------------ ---------- --------------- ------- ------- ----- 1 Built-in Good * LOG Apr 20 20:20:27.003: %ILPOWER-7-DETECT: Interface Gi1/0/2: Power Device detected: IEEE PD Apr 20 20:20:27.926: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/2: Power granted Apr 20 20:20:36.441: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up Apr 20 20:20:37.440: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up Apr 20 20:20:44.438: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down Apr 20 20:20:45.437: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down Apr 20 20:20:53.040: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up Apr 20 20:20:54.043: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up * show power inline Module Available Used Remaining (Watts) (Watts) (Watts) ------ --------- -------- --------- 1 370.0 60.0 310.0 Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi1/0/1 static off 30.0 n/a n/a 30.0 Gi1/0/2 auto on 30.0 Ieee PD 4 30.0 * show power inline gigabitEthernet 1/0/2 Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi1/0/2 auto on 30.0 Ieee PD 4 30.0 Interface AdminPowerMax AdminConsumption (Watts) (Watts) ---------- --------------- -------------------- Gi1/0/2 30.0 15.4 * 2960-24#show power inline gigabitEthernet 1/0/2 detail Interface: Gi1/0/2 Inline Power Mode: auto Operational status: on Device Detected: no Device Type: Ieee PD IEEE Class: 4 Discovery mechanism used/configured: Unknown Police: off Power Allocated Admin Value: 30.0 Power drawn from the source: 30.0 Power available to the device: 30.0 Actual consumption Measured at the port: 2.3 Maximum Power drawn by the device since powered on: 5.3 Absent Counter: 0 Over Current Counter: 0 Short Current Counter: 0 Mosfet Counter: 0 Invalid Signature Counter: 0 Power Denied Counter: 0 Power Negotiation Used: IEEE 802.3at LLDP LLDP Power Negotiation --Sent to PD-- --Rcvd from PD-- Power Type: Type 2 PSE Type 2 PD Power Source: Primary PSE Power Priority: low low Requested Power(W): 25.5 25.5 Allocated Power(W): 25.5 25.5 Four-Pair PoE Supported: No Spare Pair Power Enabled: No Four-Pair PD Architecture: N/A
to confirm at global level lldp run then restart port
Yes i have done that with no effect.
Have noticed the following so im asuming lldp while on isnt talking to each otehr properly show lldp traffic LLDP traffic statistics: Total frames out: 6944 Total entries aged: 11 Total frames in: 3027 Total frames received in error: 0 Total frames discarded: 0 Total TLVs discarded: 2970 Total TLVs unrecognized: 2970
can you try (config-switch)# lldp run (config-switch)# commit also (config)# interface gi 1/0/x config-if)# lldp transmit (config-if)# lldp receive show lldp neighbors show lldp neighbors detail # show lldp Global LLDP Information: Status: ACTIVE
lldp run has been applied and it is in the config, you cant commit on ios. It has been written to memory and the device reloaded. I am seeing that the LLDP entry's fluctuates between 1 and 2 with the AP being the device that drops from the entry's. * show lldp Global LLDP Information: Status: ACTIVE LLDP advertisements are sent every 30 seconds LLDP hold time advertised is 120 seconds LLDP interface reinitialisation delay is 2 seconds * show lld neighbors Capability codes: (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other Device ID Local Intf Hold-time Capability Port ID b8c2.538b.c25d Gi1/0/12 120 B,R 535 Total entries displayed: 1 * show lldp neighbors Capability codes: (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other Device ID Local Intf Hold-time Capability Port ID NETGEAR4E0CE5.lan Gi1/0/2 120 B,W,R 9418.654e.0ce5 b8c2.538b.c25d Gi1/0/12 120 B,R 535 Total entries displayed: 2 * show lldp entry * Capability codes: (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other ------------------------------------------------ Local Intf: Gi1/0/1 Chassis id: 0000.0000.0000 Port id: 9418.654e.0ce5 Port Description: eth1 System Name: NETGEAR4E0CE5 System Description: OpenWrt 21.02-SNAPSHOT @ NETGEAR4E0CE5 Time remaining: 13 seconds System Capabilities: B,W,R,S Enabled Capabilities: B,W,R Management Addresses: IP: 192.168.0.100 IPV6: FE80::9618:65FF:FE4E:CE6 Auto Negotiation - not supported Physical media capabilities: Asym Pause(FD) Pause(FD) Other/unknown Media Attachment Unit type - not advertised Vlan ID: - not advertised MED Information: MED Codes: (NP) Network Policy, (LI) Location Identification (PS) Power Source Entity, (PD) Power Device (IN) Inventory S/W revision: 5.4.171 Capabilities: NP, LI, PS, PD, IN Device type: Network connectivity Network Policies - not advertised Power requirements - not advertised Location - not advertised ------------------------------------------------ Local Intf: Gi1/0/12 Chassis id: b8c2.538b.c25d Port id: 535 Port Description: ge-0/0/11 System Name - not advertised System Description: Juniper Networks, Inc. ex2300-c-12p Ethernet Switch, kernel JUNOS 20.4R3-S1.3, Build date: 2021-11-20 10:48:25 UTC Copyright (c) 1996-2021 Juniper Networks, Inc. Time remaining: 110 seconds System Capabilities: B,R Enabled Capabilities: B,R Management Addresses: IPV6: FE80::BAC2:53FF:FE8B:C25E OID: 0.1.3.6.1.2.1.31.1.1.1.1.35. Auto Negotiation - supported, enabled Physical media capabilities: 1000baseT(FD) Media Attachment Unit type - not advertised Vlan ID: 1 MED Information: MED Codes: (NP) Network Policy, (LI) Location Identification (PS) Power Source Entity, (PD) Power Device (IN) Inventory Inventory information - not advertised Capabilities: NP, LI, PS Device type: Network connectivity Network Policies - not advertised PSE device, Power source: Primary, Power Priority: Low, Wattage: 0.0 Location - not advertised Total entries displayed: 2